Contact with refrigerants may cause frostbite or other related injuries. The unit will only purge when it is first turned on. The purge time is set to 30 seconds to minimize refrigerant loss.

Optional side bag with eight (8) pockets holds full sized notepad, two beverages, cell phone and more.

Charge only capability for R-134a (not permitted for R-1234yf per standards). When the display reads WARNING: MAINTE- NANCE - CHANGE FILTER DRIER Press Enter key to enter filter change mode.

3. Open Refrigerant Storage Tanks liquid valve. Models with the optional refrigerant identifier 37881 The unit will display IDENTIFY REFRIG ? To make your selection use the increase and decrease keys to toggle from Y to N. Press the Enter key to make your selection and then press the Start key to start the proc- ess. JB Tools prides itself in being a trusted, internet-based retailer that its customers can rely on for quality products at reasonable prices. MODE 2 Operational Steps 1. Press the RESET key to return to SELECT MODE. Weight - Shows the weight of refrigerant being processed in each mode. JB Tools commitment to 100% customer satisfaction is unparalleled, which is why JB Tools offers its customers a best-in-class Warranty Program to all of its customers on all products sold by JB Tools. Always use the TurboRecover Recovery Machine within its design parameters. 10-foot premium YELLOW JACKET PLUS II hoses for easy connection to even hard-to-reach fittings 25% longer than the standard (15 on 37844). It should be stored in the tool tray on the top of the unit. The LCD should read CHECK OIL LEVELS. 8. 2. Death can occur without warning. When the filter drier reaches 100 lbs of refrigerant processed it will warn the user that it is nearing the end of its life.

If the unit continues to display Y or an E and the tank pressure is near the value in the table below, contact Ritchie Engineering Customer Service at (800)769-8370. Press START key to begin vacuum and charging operations.

5cfm vacuum pump capable of extended pull time periods (7 cfm on 37844). When the display reads SUPPLY TANK EMPTY disconnect blue hose. Shop Safety & Personal Protection with everyday low prices and fast shipping. FUNCTION C - WEIGHT CONVERSION. WARNING: DO NOT RECOVER CONTAMINATED REFRIGERANT WITH THIS UNIT. Tire suas dvidas lendo as respostas dadas por outros alunos como voc. Tank, Yellow Jacket 37880 SAE J-2788 Compliant Automatic Refrigerant Management System, Yellow Jacket 37882 HD 15?

Turn on the main power switch. 5. Release the key when the correct amount of oil has been added to the system. With the systems Windows-based control tablet, we can remotely access your machine and provide training to show you how to use the machine and navigate the screens.

Failure to replace the filter will cause damage to the refrigerant identifier and void all warranties related to the refrigerant identifier.

6. Y for Yes. Press the increase or decrease key to switch between Y and N. 9. Press MODE 2 for Vacuum. RECOVERING CONTAMINATED REFRIGERANT WILL VOID ALL WARRANTIES AND MY CAUSE DAMAGE TO OTHER AUTOMOBILES THAT YOU SERVICE IN THE FUTURE. All prices are in USD 2022 JB Tools Inc. Genius Ecommerce by 1Digital.

The LCD should read PUSH START. 10. Maintenance Reminders Approximate Pressure (psig) Temp (F) R-12 R-134a 65 74 74 70 80 81 75 87 88 80 96 97 85 102 115 Temp (F) R-12 R-134a 90 110 120 95 118 126 100 127 135 105 136 145 110 146 155 FILTER - MAINT-FILTER CHG DUE The 37880 has a unique filter system which ensures the refrigerant transferred to the storage cylinder is clean and moisture-free. Yellow Jacket 37840 Refrigerant Management System Automatic for R-134a with 10? 3.

Open the service hose valves. Close the service valves and disconnect the high and low side auto service hoses from the automobile. Shop Specialty Tools with everyday low prices and fast shipping. Do not use equipment in the vicinity of spilled or open containers of gasoline or other ammable substances. Note: Hoses are Date Coded to help determine age of hose. Copyright 2022 FAST Equipment, LLC. Deliberate inhalation of refrigerants is extremely danger- ous. Mode 1 Recovery Only, cont.

Fully factory tested 34-point quality check. Moisture in an A/C system can cause erratic operation and must be removed be- fore recharging the system with refrigerant. MODE 2 - Vacuum is used to vacuum air/moisture from a system previously opened to the atmos- phere. If this occurs take the appropriate steps to locate the leak and properly repair it. Tablet can print to existing shop printer (requires local area wireless network or USB cable not included). In Charge mode, how- ever, accuracy is plus or minus 1/2 ounce based on variations in air temperature and pressure. Many items shown in our price list are custom-fabricated to customers order.

When adding R-134a to the tank of either a 37880, you will need to use the tank refill adapter sup- plied in the accessory kit. Make certain all safety devices are functioning properly before operating equipment.

The LCD will read CONNECT HOSES PRESS ENTER TO CONTINUE 5. The RESET may have to be pushed more than once to return to Select Mode screen.

Semi-Automatic Single Refrigerant Recovery/Recycle & Recharge with 50 lb. The unit will prompt you when it is near the end of its life. Repeat the identification process to insure the proper identification of the refrigerant purity level. MODE 6 - Tank Refill, is used to add new refriger- ant to the storage tank. Not ready for R-1234yf? Most states, countries, etc., may require user to be licensed. 1.

Follow these steps to change the filter drier before the scheduled filter change: Hold down Decrease key and turn on main power switch on. The choices are: pounds/ounces, pounds, ounces, and kilograms.

Purge - A Y in this field indicates non- condensable gases such as air are present in the storage tank. 5.

Dispose of recovered oil in a proper manner. The unit will automatically shut off when the INLET pressure drops below 10 hg vacuum. This warranty does not cover abuse, damage from over tightening valves, or broken gauges. If the unit fails the second time follow the on screen instructions and take the appropriate steps to remove the contaminated refrigerant with a separate unit for removal of contaminated refrigerant.

15 LCD Error Messages and Potential Solution ERROR NUMBER MESSAGE DESCRIPTION TROUBLESHOOTING ERROR 1 HIGH PRESSURE HIGH PRESSURE SWITCH IS TRIPPED (NORMALY OPEN SWITCH) OPEN TANK VALVE TEST HIGH PRESSURE SWITCH CHECK SV AND CHECK VALVE OP ERROR 2 TANK FULL TANK WEIGHT OVER 80% OF CAPACITY CHECK SCALE CALIBRATION REMOVE SOME REFRIGERANT FROM STORAGE TANK ERROR 3 RECOVERY TIME OUT RECOVERY PROCESS HAS EXCEEDED 45 FACTORY DEFAULT IF AC SYSTEM CONTAINS MORE THAN 3 LBS OF REFRIGERANT IN- CREASE DEFAULT TIME CHECK FOR LEAKS (HOSES, FIT- TINGS AND AUTO AC SYSTEM ERROR 4 CHARGING TIME OUT CHARGING PROCESS HAS EXEEDED 10 MIN FACTOR DEFAULT OPEN TANK VALVES OPEN SERVICE COUPLERS SWITCH TO LOW SIDE CHARGING CHECK TANK WEIGHT (10 LB MIN) ERROR 5 NO TANK ON SCALE SCALE NOT READING TANK WEIGHT PLACE TANK ON SCALE CHECK SCALE CALIBRATION ERROR 6 TANK EMPTY REFRIGERANT BELOW 5 % OF TANK CAPACITY REFILL TANK CHECK SCALE CALIBRATION ERROR 7 NOT ENOUGH REFRIGERANT UNIT IS LOW ON REFRIGERANT (10 LB MIN) REFILL TANK ERROR 8 TANK REFILL TIME OUT TANK REFILL HAS EXCEEDED DEFAULT TIME RUN TANK REFILL MODE AGAIN CHECK FOR LEAKS TEST LOW PRESSURE SWITCH ERROR 9 VACUUM TIME OUT.

Inhalation of high concentration of refrigerant vapors is harmful and may cause heart irregu- larities, unconsciousness, or death. When the display reads WARNING: MAINTE- NANCE - CHANGE FILTER DRIER IN XX.XX LB, press the RESET key to continue. When the LCD reads SET VACUUM HOLD TIME, set the vacuum hold time by pressing and holding INCREASE or DECREASE until the desired time is shown. For all other products, please return warranty items to the main factory in Bloomington, MN, prepaid for credit, replacement, or repair, at our option. Verify the message on the LCD reads RECOVERY COMPLETE. 7. Comes with a 50Lbs tank included with the purchase of an AR2700, 115 Volts, 50/60 HZ, Single phase, PSI/KPa gauges. Release the button and press EN- TER to accept the vacuum hold time shown on the LCD.

JB Tools Customer Satisfaction Guarantee: Although JB tools is often not an authorized re-seller of all the products it sells and is often not affiliated with the manufacturers or brands of the products it sells, JB Tools stands behind all of the products it sells, because the products JB Tools sells are genuine and authentic. 4. Failure to replace the filter will cause damage to the refrigerant identifier and void all warranties related to the refrigerant identifier. If the RECOVERY HOLD option is not selected the unit will shut off at the required level of vacuum and the opera- tor must insure that the EPA standard (SAE J2211) is met. Manufacturers occasionally suggest that products be advertised at their suggested retail price. If the filter begins to turn red in color stop using the re- frigerant identifier immediately. Call 952-943-1333.

The oil removed from the auto will drain into the oil drain bottle on the side of the unit.

Press INCREASE to raise values on the display for user-input information. All hoses may contain liquid refrigerant under pressure.

9.

However, JB Tools customers can rest assured that JB Tools stands behind its Warranty Program and its Manufacturer Matching Policy,100% of the time. The information can significantly help you manage your automobile A/C repair business. Holding the button depressed will increase the rate of change.

5 Mode keys are located on the left side of the control panel.

The unit will purge the next time it is turned off and on. 2.

The filter driers are marked with a unique code that will be required to unlock the unit. See Operating Manual for complete instructions on YELLOW JACKET web page (QR code to web page below manual found under Documents tab).

Bypass vacuum time by setting time to zero (FULL CYCLE MODE only). Plug the unit into a 100-240VAC grounded power source.

An E will display on the LCD if the previous purge was insufficient to lower the non-condensable gas value below the limit. The unit will shut off automatically when either the supply tank is empty or the storage tank is full. Correction in the manner provided above shall constitute a fulfillment of all liabilities with respect to the quality, material and workman- ship of the product. 3. 3. There will be a reconditioning charge for manifolds returned to the factory for repair. Function Keys The Function Keys are used to enter data into the system in a variety of modes.

Trays for pens, small parts, tools and other misc. Filter Change Procedure if Filter Lock Out is reached. If yes is selected the unit will begin the refrigerant identification process. tank, Sales 10 Models with the optional refrigerant identifier 37881 The unit will display IDENTIFY REFRIG ? To make your selection use the increase and decrease keys to toggle from Y to N. Press the Enter key to make your selection and then press the Start key to start the process. Connect the high and low side auto service hoses to the respective high and low side service ports on the automobile A/C system.

19153) to the R-134a virgin cylinder. JB Tools provides this disclaimer to ensure there is no likelihood of confusion unduly influencing your decision to purchase this product, or any other, product from JB Tools, and to ensure there is no confusion as to the existence of any affiliation between JB Tools and the manufacturer of this product.

Shop Shop Equipment & Tool Storage with everyday low prices and fast shipping.

Responda perguntas de provas passadas e avalie sua preparao. 1. By purchasing this product from JB Tools, the manufacturers warranty, if any, potentially associated with the product may not be honored by the manufacturer. If the pressure rises to 0 psi the compressor will restart and the unit will pull down to the required 6 of mercury and hold for two minutes. Use only new lubricant to replace the amount removed during the recycling process. Press the RESET key to return to the SELECT MODE status.

To reduce the risk of re due to overheating, use the shortest possible extension cord with a minimum conductor size of #10 AWG (6 mm), 3-conductor with the ground, maximum length 25 (7.6m) from the outlet. Estude fcil! The 37880 Series units are covered by a one year parts and labor warranty. Warning: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

In addition, the display will prompt the technician for the user input needed to continue operation.